ISTA-2B 国际安全运输协会 2B测试

	更新时间 2024-12-27 20:00:00 价格请来电询价测试周期 5-7天寄样地址深圳宝安价格费用电话详谈联系电话 17324413130 联系手机 17324413130 联系人罗卓文立即询价

详细介绍

ISTA-2B 国际安全运输协会 2B测试

1 carton with packaged product

TRANSPORTATION TEST (ISTA 2B)

As per ISTA integrity test procedure 2B: 2011, the performance and integrity of the packaged product was evaluated.

Number of sample tested: One (1) carton

1. Shipping mark: Nil / (See enclosed picture )

2. Description of package:

External container size (inch)	:	Length _________ x width _____________ x depth _________

Gross weight of packaged-product (lbs)	:

Box style	:	Regular slotted container (RSC) / Full overlap slotted container (FOL) / Full telescope design style box (FTD) / Center special slotted container (CSSC) / Overlap slotted container (OSC) / Center special overlap slotted container (CSO) / Center special full overlap slotted container (SFF) / Double cover box (DC)

Form	:	Single / double / triple wall corrugated board

Box maker"s certificate	:	No / marked with ________________ lbs/sq.inch.

Joint	:	Glued joint / taped joint /Single/double/diagonal/Vertical/horizontal/stitched joint

Closed with	:	Reinforced tape or pressure-sensitive tape / adhesive / paper sealing tape / metal staples / wide crown staples / ____fixation straps)

Style	:	Top / End opening.

(See enclosed picture 1)

3. Test procedure

(A) Anticipated conditioning: [Internal use: The condition for test must confirm with CSO]

(i) Preconditioning: Laboratory ambient temperature and humidity for six (6) hours at : _______°C; _______% RH.

(ii) Extreme Cold, Uncontrolled RH (72) hours at: -29°C/

Cold, Humid (72) hours at: 5°C, 85% RH/

Controlled Conditions (72) hours at: 23°C, 50% RH/

Hot, Humid (72) hours at: 38°C, 85% RH/

Hot, Humid then Extreme Heat, Moderate RH: (72) hours at: 38°C, 85% RH and then for six (6) hours at 60°C, 30% RH/

Elevated Temperature, Uncontrolled RH (72) hours at: 50°C/

Extreme Heat, Dry (72) hours at: 60°C,15% RH/

Severe Cold, Uncontrolled RH (72) hours at: -18°C

User defined ____________________________________________.

Result:

No visible change was found on the contents of the packaged product.

(B) Compression test :

Compression test system: Apply and release test force .

Test force: ______ pounds.

The packaged-product may be not warehoused in a stacked.

Compensating factor F=

Total number of packaged-products in a stack S= (as claimed by applicant /as recommended by standard.)

[Internal use: The no.(S) was not warehoused in a stack must confirm with CSO; S= ,F= ,Wt= ,test

force=[Wtx(S-1)xFx1.4] ( F=5 if the packaged-product may be warehoused , otherwise F=4)

Remark: No puncture of carton box was observed.

(C) Vibration test (first part)

Mode of vibration: vertical linear.

Vibration frequency: ________ CPM.

Duration of testing: ________minutes and ________ seconds.

Number of impacts: 11,800.

Remark: No puncture of carton box was observed.

(D) Impact and rotational edge drop test

(a) Not to shock the top surface

Method used:	Free fall drop

Number of drops:	4

Height of drop (inches):	6

The drop sequence and orientation were listed as below:

Drop sequence	Orientation of packaged-product
1	Face	One of the smallest vertical faces
2	Face	Opposite small vertical face
3	Face	One of the largest vertical faces
4	Face	Opposite large vertical face

Method used:	Rotational edge drop

Number of drops:	2

Height of drop (inches):	8

The sequence was listed as below:

Step	Rotational edge drop
1	Sequence	Action
	1	Place the unitized load onto a flat, rigid surface such as steel or concrete.
	2	Support one of the shortest face 3 edges with a timber or support 3.5 to 4.0 in (90 to 100 mm) in height and width.
	3	Lift the opposite face 3 edge to 8 in (200 mm) off the surface.
	4	Release the edge so that it falls freely onto the flat, rigid surface.
2	The Unit Load has a length equal to or greater than twice the width and a center of gravity above the midpoint of the height. Repeat step 1 on the face 3 edge opposite the edge just tested in step 1 sequence 4.
3	The Unit Load does not has a length equal to or greater than twice the width and a center of gravity above the midpoint of the height. Repeat step 1 on one of the face 3 edges radiating 90° from the edge just tested in step 1 sequence 4.

Remark: No puncture of carton box was observed.

(b) Shock the top surface

Method used:	Free fall drop

Number of drops:	6

Height of drop (inches):	6

The drop sequence and orientation were listed as below:

Drop sequence	Orientation of packaged-product
1	Face	One of the smallest vertical faces
2	Face	Opposite small vertical face
3	Face	One of the medium vertical faces
4	Face	Opposite medium vertical face
5	Face	One of the largest vertical faces
6	Face	Opposite large vertical face